Copyright and Corporate Identity
Copyright 3D Systems, Inc. All rights reserved. Subject to change without notice. This document is copyrighted and contains proprietary information that is the property of 3D Systems, Inc. No copies of the document may be sold or given to any person or other entity.
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by 3D Systems could void your authority to operate this equipment.
Radio Frequency Transmission
This product generates 13.56 MHz using an Inductive Loop System as a Radio Frequency Identification device (RFID). This RFID device complies with the requirements specified in FCC Part 15, Industry Canada RSS-210, European Council Directive 99/5/EC, and all applicable local laws and regulations.
Operation of this device is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device referenced in this guide contains transmitter, FCC ID: 2ADGF-PJ2500
Access to the transmitter for service technicians is available through common enclosure access methods including use of common tools and removal of covers.
NOTE: Changes or modifications to this equipment not specifically approved by 3D Systems may void the user’s authority to operate this equipment.
End User Software License Agreement
Certain Third Party Software Programs may be contained in the 3D Printer firmware and require the following notifications:
Portions of this software (Win 10) Copyright © Microsoft 2022.
Portions of this software (VxWorks) Copyright © Wind River Systems, Inc.
Portions of this software (Android UI) Copyright © 1995-2015 Interionatal Business Machines Corporation and others. All rights reserved.
Portions of this software (zlib) Copyright © 1995 – 2017 Jean-loup Gailly and Mark Adler
Portions of this software (mini-gmp library) Copyright © 2007 Free software Foundation, Inc.
Portions of this software (Apache License 2.0) Copyright © 2017 The Apache Software Foundation, Licensed under the Apache License, Version 2.0.
Portions of this software (LibTIFF) Copyright © 1988-1997 Sam Leffler, Copyright © 1991-1997 Silicon Graphics, Inc.
Permission to use, copy, modify, distribute, and sell this software and its documentation for any purpose is hereby granted without fee, provided that (i) the above copyright notices and this permission notice appear in all copies of the software and related documentation, and (ii) the names of Sam Leffler and Silicon Graphics may not be used in any advertising or publicity relating to the software without the specific, prior written permission of Sam Leffler and Silicon Graphics.
THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
Portions of this software (Boost) Copyright © Beman Dawes, Daniel Frey, David Abrahams, 2003-2004 Copyright Rene Rivers 2004-2005. The Boost license is open source; the Open Source Initiative certified the Boost Software License 1.0 in early 2008.
Portions of this software (7-Zip) Copyright © 1999-2017 Igor Pavlov.
Portions of this software (Putty) Copyright © 1997-2017 Simon Tatham.
Portions of this software (Notepad++) Copyright © 2007 Free Software Foundation, Inc.
Portions of this software (TightVNC) Copyright © 1989, 1991 Free Software Foundations, Inc.
Portions of this software (Tinyxml) Copyright © 1995-2017 Jean-loup Gailly and Mark Adler.
Portions of this software (Minicsv) Copyright © 2015-2017 Frank Denis.
Libpng versions 1.0.7, July 1, 2000 through 1.6.30, June 28, 2017 are Copyright (c) 2000-2002, 2004, 2006-2017 Glenn Randers-Pehrson, are derived from libpng-1.0.6, and are distributed according to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors: Simon-Pierre Cadieux, Eric S. Raymond, Mans Rullgard, Cosmin Truta, Gilles Vollant, James Yu, Mandar Sahastrabuddhe, Google Inc., Vadim Barkov.
Portions of this software (Google-test) Copyright © 2008, Google Inc. All rights reserved.
Portions of this software (Rapidjson) Copyright © 2015 THL A29 Limited, a Tencent company, and Milo Yip. All rights reserved. The Msinttypes r29 Copyright © 2006-2013 Alexander Chemeris. All rights reserved.
Portions of this software (SimpleJSON) Copyright © 2006 Bob Ippolito.
Portions of this software (SQLite) Copyright © 2008-2012 Zetetic LLC. The code for SQLite has been dedicated to the public domain by the authors.
Portions of this software (JPEG) is Copyright (C) 1991-1998, Thomas G. Lane. All Rights Reserved except as specified below.
Portions of this software (Chilkat) Copyright © 2000-2017 Chilkat Software, Inc. All rights reserved.
Portions of this software (OpenDHCP) Copyright © 2007 Free Software Foundations, Inc.