3D Systems’ Infocenter Moves to Salesforce

The Infocenter has been the 3D Systems portal for customer-facing and service-facing product documentation (for example videos, software downloads, and material SDSs).  

As of Sept 26, 2022, the Infocenter content will be moved to Salesforce and will be accessible through the Salesforce Community

Service Documentation Only

To access service documentation, you will need to sign into Salesforce Community using your Salesforce username and password. Everyone trained and currently authorized to service a particular printer will be able to access its service documentation.

If you have any issues or need assistance, please contact the

Thank you for purchasing the Figure 4 Standalone 3D Printer.

The Figure 4 Standalone Printer is a flexible and efficient projector-based 3D-printing system that produces high-fidelity parts from a broad range of materials. The Figure 4 Standalone Printer uses a digital-projection light source and a special membrane-based resin tray that enables very high print speeds and new material chemistries that provide production-grade properties. It is intended to be used as a three-dimensional output device to create (or to communicate design intent of) durable, end-use parts. Parts produced can be used in all phases of design, from a concept build to functional testing and end-use parts. The Figure 4 Standalone Printer uses all Figure 4 resins for a variety of applications.

These parts are generated in the rapid prototyping (RP) environment under the control of the printer operators. The system must be run by technicians who are trained in proper usage of the printer and resins. All design and process considerations are compatible with an RP environment. The three-dimensional solid parts that are printed consist of different print materials that cure when exposed to 405 nm radiation. The operator pours print material, also called "resin," into the resin tray. Using a proprietary digital projector that 3D Systems has developed, a radiation pattern is cast onto the underside of the resin tray and through to the bottom of the resin. This radiation causes a phase change in the resin that converts it into a solid polymer, adhering to the print platform. After a layer has cured, the elevator moves the print platform up by one layer length and the radiation pattern for the next layer is projected. This process repeats, layer by layer, until the build file is complete. The print platform, along with the part, is removed from the printer and the part is cleaned and post-cured to provide a finished part.

This manual provides users with an understanding of features, system requirements, and operating procedures needed to create finished parts using the Figure 4 Standalone Printer.

Copyright and Corporate Identity

Figure 4® is a registered trademark of 3D Systems.


3D Systems may (but shall not be obligated to) make improvements to this document from time to time. However, the Licensed User acknowledges that at any time after the expiration of the date of issuance, 3D Systems may institute a periodic charge or fee payable by the Licensed User in return for ongoing receipt of improvements. It is the responsibility of the Licensed User to provide 3D Systems with current information as to its name and address. The Licensed User also undertakes to notify 3D Systems promptly in the event that it considers any of the data contained in this document to be incomplete or erroneous in any respect, in connection with the Licensed User’s particular or general use.

FCC Notice

United States

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with these instructions, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.


CAN ICES-3 (A)/NMB-3 (A)

European Union

CAUTION: This is a Class A product. In a domestic environment, this product can cause radio interference in which case the user could be required to take adequate measures.



사용자 안내문

이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서 가정용 환경에서 사용하는 경우 전파간섭의 우려가 있습니다.

Changes or modifications to this equipment not approved by 3D Systems can void the authority of the user to operate this equipment.