Skip to main content
Toggle navigation
3D Systems.com
Customer Support Center
Infocenter
Shop
Infocenter
Service Sign In
Language
Search form
3D Printers
Software
Materials
Finishing
Support Services
Legacy Printers
Search form
English
中文
Français
Deutsch
Italiano
日本語
한국어
Português
Español
User Guide
Operation
Firmware Update
Firmware Update
The Figure 4 Modular has two sets of firmware:
Drives operation of the Controller
Drives operation of a Printer
Printer-friendly version
Controller Firmware Update
Printer Firmware Update
‹
Shut Down Figure 4 Modular Components
up
Controller Firmware Update
›
Printer-friendly version
Resin Tray Care
Facility Requirements
Introduction
Figure 4 Modular
Figure 4 UV Curing Unit 350
NextDent LC-3DPrint Box
Part-Preparation Software
Site Selection - Figure 4 Modular Base Unit
Part 1
Part 2
Part 3
Site Selection - Post-Processing Equipment
System Delivery
Preparation for Receiving
Transporting the Figure 4 Modular Components
Shipment Arrival
Weights and Measurements Charts
Third-Party Supplies and Equipment
System Installation
Resin Storage and Safety
3D Connect
Figure 4 Modular Advance Preparation Checklist
Obtaining Assistance
Quick Start Guide
Introduction
Important Safety Information
At a Glance
Controller User Interface
Printer Startup and Demo Build
Shut Down Figure 4 Modular Components
User Guide
Introduction
Safety
Safety Switches
Material Handling and Safety
Environmental Safety
Electrical Safety
Compressed Air Safety
Emergency Shutdown
First Aid and Protective Equipment
Safety Notice
Label Installation Diagram
Overview
Figure 4 Modular Components
Controller
Printer
Upper Build Chamber
Upper Print Engine
Resin Tray
Print Platform
Carbon Filter
Lower Build Chamber
Catch Tray
Material Delivery Module (MDM)
Material Cartridge
Top of Printer
Leveling Feet
Specifications and Requirements
Figure 4 Material Cartridges
Special Considerations for FLEX BLK 10
System Requirements and Setup
Power on Modular System
Installing/Setting Up 3D Sprint Software
Find Modular System on Network
Considerations for Figure 4 Printing
3D Sprint Additional Documentation
Supplied Accessories
Optional Accessories
3D Connect
Operation
Controller User Interface
Status Screen
Printer - Expanded View
Material Card
Material Information
Build File Card
Detailed Job Data Card
Printer Info Card
Printer Network Settings
Resin Tray Card
Resin Tray Status
Printer Status
Cartridge Status
Fly-out Menu
Adjust GUI Appearance
Printer Icons
Queue Screen
Queue Toolbar
Active Print Jobs
Pending Print Jobs
Completed Print Jobs
Settings Screen
System Controls
Network Settings
Localization
FW/SW Version
Diagnostics Logs
Adjust the Touch Screen
Printer User Interface
Printer Messages
Code Blue Messages
Code Yellow Messages
Code Red Messages
Code Gray Messages
Load Material Cartridges
Premix Material Before Cartridge Installation
Resin Mixer
Replace Empty Cartridge
Prepare and Install the Print Platform
Install Print Platforms
Install Resin Tray
Resin Tray Guidelines
Fill Resin Tray with Material
Fill Resin Tray from Empty
Resin Tray Material Cross-Usage
Material Changeover
Remove/Replace MCO Tubing
Print Job Overview
Add a Job to the Print Queue via USB
Editing Build File Properties
Abort Print Job
After Aborting
Job Queue Assignment
Running a Resin Tray Cleaning After a Failed Build
Light Stack Errors/Alarms
Shut Down Figure 4 Modular Components
Firmware Update
Controller Firmware Update
Printer Firmware Update
Add New Material in 3D Sprint
Moving the Printer/Controller in Your Facility
Preventative Maintenance
Cleaning the Printer
Clean/Replace the Catch Trays
Clean Resin Trays
Clean Print Platform
Clean Membrane-Interface Lip
Clean Upper-Build-Chamber Door
Clean the Touch Screen and Keyboard
Clean Projector Lens
Clean Tension Arms
Clean Drip Trays
Changing Out the Carbon Filter
Check Print-Platform Level
Troubleshooting
Printed Part Quality
Hardware Issues
Network Issues
Firmware Issues
Printer Message Glossary
Service and Support
EC Declaration of Conformity
Post-Processing
About this Manual
Important Safety Information
Post Processing Instructions
Remove Print Platform
Remove Printed Parts From Platform
Cleaning Parts Printed with Figure 4 Resins
Figure 4 Cleaning Charts
Cleaning Parts Using an Ultrasonic Cleaner
Cleaning Parts Manually
Specific Gravity Measurement
Dry the Build Parts
UV Cure the Parts
General Post-Curing Requirements
Material Curing Chart
Sterilization Protocol for MED-AMB 10
Considerations for Heating Figure 4 HI TEMP 300-AMB
Clean Print Platform
Clean Resin Tray
Clean Finishing Tools
Troubleshooting
Figure 4 UV Curing Unit 350 User Guide
Introduction
Safety
Safety Switches
Green Part Handling and Safety
UV Safety
Environmental Safety
Electrical Safety
Emergency Shutdown
First Aid and Protective Equipment
Safety Notice
Label Installation Diagram
Overview
Inside the Unit
Back of the Unit
Accessories
Specifications and Requirements
Supported Print Materials
Installation
Unpacking the UV Curing Unit 350
Install the UV Lamps
Operation
Power on UV Curing Unit 350
Prior to Usage
Cure Your Printed Parts
Shut Down the Unit
Preventative Maintenance
Changing Out UV Lamps
Broken Fluorescent Lamps
Changing Out the Carbon Filter
Cleaning the Shelving Unit
Cleaning the Rest of the Unit
Troubleshooting
Service and Support
CE Declaration of Conformity
Guides Inside the Box
UV Curing Unit 350
Software Downloads
Accessories
Customer Information Bulletins
Best Practices
Video Tutorials
Warranty