NOTE: Unless governed by prior arrangement, 3D Systems is not responsible for loading 3D Sprint software on the user’s workstation(s). Thus, BEFORE THE 3D PRINTER SYSTEM ARRIVES, ensure that your workstation is capable of supporting the requirements of both 3D Sprint software and communication with the printer via your network.
If you wish to fill out this form by hand:
Press ctrl+P (cmd+P on Mac) to print this page. Fill out the form, make a copy for yourself, and fax/email it to your reseller.
If you wish to fill out this form on your computer:
Fill out the information in ALL the fields, and then press ctrl+P (cmd+P on Mac) to print the document. Then sign and date the document by hand, make a copy for yourself, and fax/email it to your reseller.
Review this list with a network administrator, IT department, facilities manager, and/or other responsible person within your organization. Please complete the following information:
This is NOT an online form and CANNOT be submitted on this webpage. The form must be printed out and faxed/emailed.
|Telephone (with area code):|
|Contact (print full name):|
Please place a check in each box once that item is complete.
|Operating system and workstation configurations are compatible and meet the minimum requirements as stated in the 3D Sprint Software section.|
|Final installation site is selected. The intended physical location for the printer should be selected in advance, and checked for adherence to the guidelines set out in this guide.|
|Flooring where printer will be located is non-porous, has an incline of less than/equal to 2.5 cm/12 m (1 in/40 ft), and is isolated from significant sources of vibration.|
|Flooring can take the total weight of all system components combined in the room(s) they are in.|
|Enough surge-protected circuits have been installed to accommodate the number of printers, and other products, ordered. Enough power outlets have been installed on these circuits.|
|If desired/required, you have purchased enough uninterrupted power supplies (UPS) for the number of printers, and other products, ordered.|
|You have a print-material-storage area set up that can be kept at 5°C-30°C (41°F-86°F). Temperature of 3D-printing room can be kept at 18-28°C (64.4-82.4°F).|
|3D-Printing room can be kept between 30-70% relative humidity (RH).|
|3D-Printing room is less than 2,400 m (1.5 mi) above mean sea level.|
|HVAC can perform at least six air changes per hour and 3D-Printing room is well-ventilated and has clean air.|
|3D-printing room lighting is either fluorescent lamps with clear-plastic diffusers, or has sufficient UV filters covering its lights.|
|Both the 3D-printing room and material-storage area can be isolated in the event of a resin spill or open-radiation Service call.|
|A method of removing the crate from the shipper’s truck has been arranged, such as a pallet jack or forklift, and is available to transfer the crate(s) to the uncrating location.|
|For removing the printer from its crate, you have another person available to help team lift it. For transporting the uncrated printer within your facility, you have the help of another person or hand truck.|
|Your receiving area, hallways, and 3D-printing room have the necessary doorway/passageway clearance to move either crated or uncrated components of the Figure 4 Jewelry system.|
|You have set up hazardous waste containers, as well as arranged for a company to dispose of your hazardous waste according to all government regulations.|
|You have purchased any desired third-party supplies and equipment.|
|Enough Cat-5e/Cat-6 Ethernet outlets have been installed to accommodate the number of printers you have ordered.|
|If Figure 4 Jewelry system will use 3D Connect™, an internet connection via gateway/NAT, using port 443 with encrypted connections is available.|
|Final installation site is selected. The intended physical location of your post-processing equipment should be selected in advance, and checked for adherence to the guidelines set out in this guide.|
|For the LC-3DPrint Box: A surge-protected circuit with space for a 1.3A (2.6A USA) machine is available.|
|If purchasing an ultrasonic cleaner, it is rated for use with flammable solvents like IPA (isopropyl alcohol). Larger ultrasonic cleaners may require a dedicated circuit and/or power outlet. Check with your ultrasonic cleaner supplier.|
|If desired/required, you have purchased enough uninterrupted power supplies (UPS) for your post-curing units and ultrasonic cleaners.|
|If desired/required, fume hoods have been installed in your part-cleaning/curing areas.|
Before the printer is installed into this facility, we acknowledge that the installation site complies with the specifications stated in the Figure 4 Jewelry Facility Requirements Guide. Once the printer is installed, we agree not to alter any of the required specifications listed in this manual without consulting with a 3D Systems’ Customer Service Representative or certified partner. If alterations are made without consulting 3D Systems, it may void the system’s warranty.