Unpacking And Initial Setup

CAUTION: Due to the size and weight of the printer, this procedure may require more than one person. Ensure there are enough people to safely and comfortably move the printer to its final location.

NOTE: Ensure that you save all foam and packing material for the future repacking of your CubePro. Transporting the printer without original packing materials may damage the printer

  1. Carefully cut the straps if applicable and then pull the tabs on all four release clips.

NOTE: There is one release clip on each side of the box.

  1. Pull the handles (A) and remove the release clips from the outer box.

  1. Lift the box away from the printer.

  1. Remove the accessories tray (A).

  1. Remove the upper foam supports (A) from the printer.

  1. Pull the protective bag down around the printer and remove the printer assembly from the lower foam support.

  1. Position the printer where it will be used.

NOTE: Ensure the printer is placed in a location where its size and weight will be properly supported.

 

  1. Unpack the top layer of the accessories tray.

NOTE: Depending on the printer configuration, the arrangement of the accessory boxes may differ. Unpack the power cord (A), the spacer (B), material cartridge, tool kit and Cube Glue(C). Your configuration may include 1, 2 or three cartridges. For configurations with fewer than three cartridges included, empty boxes may be used as spacers.

  1. Unpack the bottom layer of the accessories tray.

NOTE: Depending on the printer configuration, the arrangement of the accessory boxes may differ. Unpack the print pad (A), the jet wiper assembly (B), and material cartridges (C). Your configuration may include 1, 2 or 3 cartridges. For configurations with fewer than three cartridges included, empty boxes may be used as spacers.

CAUTION: The print pad is fragile. Exercise caution when handling the print pad.

  1. Open the front door. Cut away the zip ties (A) and remove the foam tubing from the print jet area.

NOTE: For illustration purposes only, the door was removed from the image. Do not attempt to remove the door from the printer.

  1. Loosen and remove the four (4) 4mm screws securing the Z-Axis guard and remove the guard. Save the guard and screws for future repacking.

  1. Using a 4mm hex head driver, attach the mounting posts to the jet wiper assembly with the supplied screws and washers.

NOTE: Tighten the screws until the posts are secure.

CAUTION: Do not over-tighten the screws. The jet wiper assembly can break if the screws are over-tightened.

  1. Move the jet wiper assembly to the back of the printer and locate the keyhole slots (A).

  1. Mount the jet wiper mounting posts to the back panel of the printer through the keyhole slots.

NOTE: Slide the mounting pins downward.

  1. Align the jet wiper assembly bottom tab (A) with the slot in the floor (B) and slide the jet wiper assembly downward.

NOTE: If the jet wiper assembly is fully seated into the keyhole slots but the bottom does not rest on the thumbscrew head, remove the jet wiper and turn the thumbscrew counter-clockwise until the jet wiper bottom rests on the thumbscrew head and the keyhole slots are fully seated. This may require repeated removals and re-installations of the jet wiper. If the keyhole slots will not seat, the thumbscrew may need to be adjusted downward by turning clockwise.

NOTE: Refer to the section titled Adjusting the Jet Wiper for information about adjusting the jet wiper scraper height.

  1. Remove the print pad from the box and place it onto the print platform with the round magnet on the bottom of the pad inserted into the triangular opening on the platform. Ensure the print pad is securely seated on the print plate.

  1. Connect the power cord to the power inlet port (B) on the right side of the printer and the other end to a wall outlet. Press the power on/off switch (A) to power on the CubePro.

Power_Input_and_Switch4_sm-72-01.png

  1. Press the on/off button (A) beside the LED screen to power on the CubePro touchscreen display.

CubePro_Display_a_sm-72-01.png

  1. Press the touchscreen to navigate to the main menu.

NOTE: Turning on the touchscreen will also turn on the interior LED lights.