General Tips for All Materials |
- Use orientation to minimize large cross sections areas. Orient parts per best practices and on YouTube Module 3 & 4 tips.
- For full platforms and parts with cross sectional areas, print quality is best in Premium mode. Or add 1-2 seconds to slow down the Interval Pause Time and the Interval Down Time in the Build Style by an extra 1-2 seconds.
- Large flat bottom surfaces can be improved by increasing cure depth from 10-20%, pending effects of fine features.
- Verify all holes, bosses, and fine features are supported properly when using auto-generated supports. If support issues occur, increase density of supports and tip ratio.
- For large parts, dense arrays of parts, or negative features in bottom of part, you might wish to clean the parts while still on the print platform. If this is the case, increase Minimum Support Height to 5-7 mm to make cleaning under the parts easier.
- May need to remove the bottom of bulk of supports (not tips) before cleaning. Allowing part to dry before removing supports allows for less scratching of part.
- After a curing cycle in the LC-3DPrint Box, the glass plate inside will be hot. To prevent part warping, avoid placing green parts on the glass plate when it is still hot. For best results on large or flat parts:
- Post-cure for 20 minutes on the build platform and allow five minutes to cool
- Remove part from build platform and remove supports.
- Cure the part on the glass for the standard amount of time listed in the chart below.
|
n/a |
n/a |
n/a |
n/a |
Figure 4 PRO-BLK 10 |
General best practices apply. |
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
90 min. (see Note 2) |
Figure 4 HI TEMP 300-AMB |
- General best practices apply.
- Manual clean only - do not use sonication.
|
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
no mixing necessary
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
90 min. (see Note 2) |
Figure 4 MED-AMB 10 |
-
General best practices apply.
-
To avoid chipping printed part during post processing, do not support part too close to its edges in 3D Sprint.
-
To avoid areas of color differences on your parts, space parts well in LC-3DPrint Box to avoid parts casting shadows on each other.
|
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
New bottle - 5 min.
After 1st use - 5 min.
(see Note 1)
Mix resin in resin tray before printing
In tray < 3 hr - 10 sec.
In tray > 3 hr - 30 sec.
|
Post-Processing Guide
Cleaning Charts
|
60 min. (see Note 2) - After curing, sterilize in autoclave according to User Guide. |
Figure 4 MED-WHT 10 |
-
General best practices apply
-
To avoid chipping printed part during post processing, do not support part too close to its edges in 3D Sprint.
-
For best results use the Resin Mixer to gently stir between prints and after the print material has been sitting overnight.
 |
CAUTION: Do NOT press down on the film when stirring.
|
-
Must keep clean bath of IPA to reduce color changing. Best to keep white material separate form other material to avoid color contamination
-
White pigment is very difficult to clean off print platforms. Soak print platforms in solvent, and then wipe with solvent-wetted towels.
|
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Before Pouring
New bottle - Hand-shake for 5 mins., then place on LC-3DMixer for 2.5 hr.
After 1st use - Hand-shake for 5 mins., then place on LC-3DMixer for 1 hr.
(see Note 1)
Mix resin in resin tray before printing
In tray < 3 hr - 30 sec.
In tray > 3 hr - 60 sec.
|
Post-Processing Guide
Cleaning Charts
|
60 min. (see Note 2) - After curing, sterilize in autoclave according to User Guide. |
Figure 4 RUBBER-BLK 10 |
- General best practices apply.
- Material is soft when green. You must orient it in 3D Sprint to allow for the maximum number of support locations.
- Tall parts (>100 mm) print best at 30 µm layer thickness.
- Take care when handling green parts due to their flexible nature.
- IPA does not dissolve this material. Propylene Carbonate must be used when cleaning printed parts. IPA should only be used as a final rinse.
- Parts can be sticky until post cured.
|
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
90 min. (see Note 2) |
Figure 4 FLEX-BLK 20 |
General best practices apply. |
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
90 min. (see Note 2) |
Figure 4™ FLEX BLK 10 |
-
General best practices apply.
-
Orient part in 3D Sprint to such that flat surfaces are not parallel with the print platform. Flat surfaces may show more support scarring than other Figure 4 materials.
|
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
60 min. (see Note 2) |
Figure 4 EGGSHELL-AMB 10 |
- General best practices apply.
- When using parts to create injection molds, keep supports on the part to hold it steady during injection and current process of silicones.
- There are many commercial silicone and RTV materials used for eggshell molding. Use the following during post-processing with EGGSHELL-AMB 10 to improve any inhibition issues:
- When cleaning parts, use acetone instead of IPA, following the same cleaning instructions for IPA from the Post-Processing Guide. Follow all SDS and safety precautions when using any solvent for cleaning parts.
- Dry parts in an oven at 60°C (140°F) for one hour before post curing.
- Post-cure parts for 180 minutes.
- Reheat parts for one hour at 100°C (212°F).
- Cure injected materials at an elevated temperature, such as 60°C (140°F), for one hour if material allows.
- Clean parts with soapy water after post-curing. Dry parts thoroughly.
|
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
no mixing necessary
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
90 min. (see Note 2) |
Figure 4 TOUGH-BLK 20 |
General best practices apply.
|
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
90 min. (see Note 2) |
Figure 4™ TOUGH-GRY 10 |
- General best practices apply.
- For best results use the Resin Mixer to gently stir between prints and after the resin has been sitting overnight.
 |
CAUTION: Do NOT press down on the film when stirring.
|
|
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
60 min. (see Note 2) |
Figure 4™ TOUGH-GRY 15 |
- General best practices apply.
- For best results use the Resin Mixer to gently stir between prints and after the resin has been sitting overnight.
 |
CAUTION: Do NOT press down on the film when stirring.
|
|
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
90 min. (see Note 2) |
Figure 4™ ELAST-BLK 10 |
- General best practices apply.
- Remove parts from platform after printing. After 12 hours, large parts can detach from print platform and fall into material tray.
|
Video - Figure 4 Standalone 3D Sprint Training
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
45 min. (see Note 2) |
Figure 4™ JCAST-GRN 10 |
-
Manually check support locations in 3D Sprint before printing.
-
In thicker cross sections for large rings or non-ring geometries, go up in cure depth to avoid delamination between layers. Go up in 10 µm increments to prevent over curing features.
-
For full platforms and parts with cross sectional areas, print quality is best in Premium mode. Or add 1-2 seconds to slow down the Interval Pause Time and the Interval Down Time in the Build Style by an extra 1-2 seconds.
-
If positive features have poor resolution, the Border Thickness parameter in the build style could be increased up to 20%. It is not suggested to go higher, or negative features might get closed or too small.
-
If detail is blurry, verify proper cleaning method. Ensure cleaning solvents are not saturated and parts are allowed to dry before post curing.
-
If detailing is still blurred, lower cure depth in 10 µm increments.
-
If detail remains an issue, or accuracy is hard to achieve, run the accuracy wizard for this build style.
-
Make sure all IPA has evaporated off after part cleaning, and allow for parts to dry completely. If surface finish is still shiny (not matte) after cleaning, not all print material has been removed and it will show up in the casting. Repeat cleaning and drying until parts do not have any excess material.
|
Video - Jewelry
3D Sprint YouTube Videos
Click here for full material best practices
|
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
30 min. (see Note 2) |
Figure 4™ RUBBER-65A BLK |
- General Best Practices Apply.
- Remove parts from platform after printing. After 12 hours, large parts can detach from print platform and fall into material tray.
- Parts should be cleaned and cured soon after removing from the printer for best results.
- Aged material may have a different color hue, but it does not affect part building or usage.
|
Click here for full material best practices |
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
90 min. (see Note 2) |
Figure 4™ JEWEL MASTER GRY |
- General Best Practices apply.
- Due to the delicate geometry of jewelry, it is a best practice to use the Modify tab to Add/Remove supports for optimal outcome.
- Use the cure depth adjustment under the Advanced section of the Build Style window to resolve fine or negative features when necessary. Adjustments should be within 10-20 µm increments.
- IPA already dirty with Jewel Master GRY resin cleans slightly better than using only fresh IPA. Using a two-step dirty IPA/clean IPA cleaning process works best.
- Remove support tips before part is completely dry to avoid damaging the part.
- Post cure parts before sanding support nibs flush. Parts are weaker than supports prior to post curing. After post curing, parts and supports have equal strength and sanding gives the desired result.
|
Click here for full material best practices |
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
60 min.
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Figure 4™ RIGID WHITE |
|
Click here for full material best practices |
Pre-mix resin on LC-3DMixer before pouring
New bottle - 1 hr.
After 1st use - 10 min.
(see Note 1)
Mix resin in resin tray before printing
30 sec.
|
Post-Processing Guide
Cleaning Charts
|
90 min. (see Note 2) |