Figure 4 Resin Quick Reference

You can you use the following chart as a one-stop shop for all Figure 4 print material information.

To print this page, scroll to the bottom and click the Printer-friendly Version Link. On the page in the new tab, press ctrl+P (cmd+P on Mac) to print the document. For best results, set up the print in landscape orientation and 50% scale.

Print Material Accuracy Tips 3D Sprint Orientation / Supports Guides Resin Mixing Instructions Part-Cleaning Info. Part-Curing Time
Figure 4™ TOUGH-GRY 10
  1. Use orientation to minimize large cross sections areas.
  2. For full platforms and parts with cross sectional areas, print quality is best in Premium mode. Or add 1-2 seconds to slow down the Interval Pause Time and the Interval Down Time in the Build Style by an extra 1-2 seconds.
  3. For best results use the Resin Mixer to gently stir between prints and after the resin has been sitting overnight.

    CAUTION: Do NOT press down on the film when stirring.

  4. Verify proper cleaning method. Insure cleaning solvents are not saturated and parts are allowed to dry before post cure.

Video - Figure 4 Modular 3D Sprint Training

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.


Mix resin in resin tray before printing

30 sec.

Post-Processing Guide 60 min (see Note)
Figure 4™ TOUGH-GRY 15
  1. Use orientation to minimize large cross sections areas.
  2. For full platforms and parts with cross sectional areas, print quality is best in Premium mode. Or add 1-2 seconds to slow down the Interval Pause Time and the Interval Down Time in the Build Style by an extra 1-2 seconds.
  3. For best results use the Resin Mixer to gently stir between prints and after the resin has been sitting overnight.

    CAUTION: Do NOT press down on the film when stirring.

  4. Verify proper cleaning method. Insure cleaning solvents are not saturated and parts are allowed to dry before post cure.

Video - Figure 4 Modular 3D Sprint Training

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.


Mix resin in resin tray before printing

30 sec.

Post-Processing Guide 90 min.(see Note)
Figure 4™ ELAST-BLK 10
  1. Use orientation to minimize large cross sections areas.
  2. For full platforms and parts with cross sectional areas, print quality is best in Premium mode. Or add 1-2 seconds to slow down the Interval Pause Time and the Interval Down Time in the Build Style by an extra 1-2 seconds.
  3. Remove parts from platform after printing. After 12-hours large parts can detach from print platform and fall into material tray.
  4. For best results use the Resin Mixer to gently stir between prints and after the resin has been sitting overnight.

    CAUTION: Do NOT press down on the film when stirring.

  5. Verify proper cleaning method. Insure cleaning solvents are not saturated and parts are allowed to dry before post cure.

Video - Figure 4 Modular 3D Sprint Training

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.


Mix resin in resin tray before printing

30 sec.

Post-Processing Guide 45 min.(see Note)
Figure 4™ FLEX-BLK 10
  1. Use orientation to minimize large cross-sectional areas.

  2. Orient part to print non-flat surfaces. Flat surfaces may show more support scarring than other Figure 4 materials.

  3. For full platforms and parts with large cross-sectional areas, print quality is best in Premium mode. Alternatively, you could go into the Build Style menu and add 1-2 seconds to both the Interval Pause Time and Interval Down Time.

  4. Verify proper cleaning method. Ensure cleaning solvents are not saturated and parts are allowed to dry before post curing.

Video - Figure 4 Modular 3D Sprint Training

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.


Mix resin in resin tray before printing

30 sec.

Post-Processing Guide 60 min.(see Note)
Figure 4™ MED-AMB 10
  1. Orient drill guide holes perpendicular to the XY-Plane.  If there are multiple drill guides at different angles try to orient the part to keep them all as perpendicular to the XY-Plane as possible.

  2. Verify proper cleaning method. Insure cleaning solvents are not saturated and parts are allowed to dry before post cure.

Video - Figure 4 Modular 3D Sprint Training

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.


Mix resin in resin tray before printing

30 sec.

Post-Processing Guide 60 min. (see Note) - After curing, sterilize in autoclave according to User Guide.

NOTE: Ensure that you place the build in your UV curing oven in the same orientation it was printed in, as if the bottom of the oven is the print platform.