1. Figure 4 Best Practices
  2. Figure 4 Modular
  3. Figure 4 Material Quick Reference

Figure 4 Material Quick Reference

You can you use the following chart as a one-stop shop for all Figure 4 print material information. To print this page, scroll to the bottom and click the Printer-friendly Version Link. On the page in the new tab, press ctrl+P (cmd+P on Mac) to print the document. For best results, set up the print in landscape orientation and 50% scale.

Print Material Material Tips 3D Sprint Orientation / Supports Guides Print Material Mixing Instructions Part-Cleaning Info. Part-Curing Time
General Tips for All Materials
  1. For best results, orient part to try and maintain uniform wall thickness.
  2. For full platforms and parts with cross sectional areas, print quality is best in Premium mode. Or add 1-2 seconds to slow down the Interval Pause Time and the Interval Down Time in the Build Style by an extra 1-2 seconds.
  3. Use Standard Thick mode for thick parts or densely packed print platform. Thick part for example is 20x20x10.
  4. Use orientation to minimize large cross sections areas. Orient parts per best practices and on YouTube Module 3 & 4 tips.
  5. Large flat bottom surfaces can be improved by increasing cure depth from 10-20%, pending effects of fine features.
  6. Verify all holes, bosses, and fine features are supported properly when using auto-generated supports. If support issues occur, increase density of supports and tip ratio.
  7. Ensure parts are not supported on a line of supports. Best results have three supports similar to a tripod preventing the part from moving side to side during the print.
  8. For large parts, dense arrays of parts, or negative features in bottom of part, you might wish to clean the parts while still on the print platform. If this is the case, increase Minimum Support Height to 5-7 mm to make cleaning under the parts easier.
  9. May need to remove the bottom of bulk of supports (not tips) before cleaning. Allowing part to dry before removing supports allows for less scratching of part.
  10. After a curing cycle in the LC-3DPrint Box, the glass plate inside will be hot. To prevent part warping, avoid placing green parts on the glass plate when it is still hot. For best results on large or flat parts:
    1. Post-cure for 20 minutes on the build platform and allow five minutes to cool
    2. Remove part from build platform and remove supports.
    3. Cure the part on the glass for the standard amount of time listed in the chart below.
 n/a n/a n/a n/a
Figure 4® PRO-BLK 10
  1. General best practices apply.
  2. When printing thick parts or very dense platforms, use Premium Plus for best results. Note mode will be ~2x slower but can provide very good part quality.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min. (see Note)
Figure 4® Rigid White
  1. General Best Practices apply
  2. Place parts a minimum of 8 mm apart to improve material flow and adhesion.
  3. If adhesion issues occur, raise the Base Layer Curing Time to 100 seconds. It may also be necessary to change Base Truss Infill Type to 'Solid' rather than 'Connected Solid'.
  4. If printing flat surfaces, reduce the Interval Distance to 3-5 mm to improve pillowing effect. Adding some supports will also improve the part.
  5. When printing thick parts or very dense platforms, use Premium Plus for best results. Note - mode will be ~2x slower but can provide very good part quality.

Click here for full material best practices

3D Sprint YouTube Videos

Hand-mix with vigorous up/down motion

Every morning, 2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min. (see Note)
Figure 4® RIGID GRAY
  1. General best practices apply.
  2. For best results use the Resin Mixer to gently stir between prints and after the print material has been sitting overnight.

    CAUTION: Do NOT press down on the film when stirring.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

Every morning, 2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min.(see Note)
Figure 4® HI TEMP 300-AMB
  1. General best practices apply.
  2. Manual clean only - do not use sonication.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

no mixing necessary

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min. (see Note)
Figure 4® High Temp 150C FR Black
  1. General best practices apply.
  2. For best results use the Resin Mixer to gently stir between prints and after the print material has been sitting overnight.

    CAUTION: Do NOT press down on the film when stirring.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min.(see Note)
Figure 4® TOUGH 65C BLACK
  1. General Best Practices apply
  2. When printing  thick parts or very dense platforms, use Premium Plus for best results. Note mode will be ~2x slower but can provide very good part quality.
  3. For best results space parts at a minimum of 10mm apart.
  4. Avoid printing parts flat. Orient parts for better flat surfaces.
  5. Parts, before and after cure can be easily scratched and show up on part surfaces.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min.(see Note)
Figure 4® TOUGH 60C WHITE
  1. General Best Practices apply
  2. Before a build, and if printer has sat overnight, stir resin in resin tray and shake Modular cartridge.

    CAUTION: Do NOT press down on the film when stirring.
  3. When printing  thick parts or very dense platforms, use Premium Plus for best results. Note mode will be ~2x slower but can provide very good part quality.
  4. For best results space parts at a minimum of 10mm apart.
  5. Avoid printing parts flat. Orient parts for better flat surfaces.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min.(see Note)
Figure 4® RUBBER-65A BLK

  1. General Best Practices Apply.

  2. Remove parts from platform after printing. After 12 hours, large parts can detach from print platform and fall into material tray.

  3. Parts should be cleaned and cured soon after removing from the printer for best results.

  4. Aged material may have a different color hue, but it does not affect part building or usage.

Click here for full material best practices

3D Sprint YouTube Videos

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min. (see Note 2)
Figure 4® RUBBER-BLK 10
  1. General best practices apply.
  2. Material is soft when green. You must orient it in 3D Sprint to allow for the maximum number of support locations.
  3. Tall parts (>100 mm) print best at 30 µm layer thickness.
  4. Take care when handling green parts due to their flexible nature.
  5. IPA does not dissolve this material. Propylene Carbonate must be used when cleaning printed parts.  IPA should only be used as a final rinse.
  6. Parts can be sticky until post cured.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min. (see Note)
Figure 4® FLEX-BLK 20

General best practices apply.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min. (see Note)
Figure 4® MED-AMB 10

  1. General best practices apply.

  2. To avoid chipping printed part during post processing, do not support part too close to its edges in 3D Sprint.

  3. To avoid areas of color differences on your parts, space parts well in LC-3DPrint Box to avoid parts casting shadows on each other.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 60 min. (see Note) - After curing, sterilize in autoclave according to User Guide.
Figure 4® EGGSHELL-AMB 10
  1. General best practices apply.
  2. When using parts to create injection molds, keep supports on the part to hold it steady during injection and current process of silicones.
  3. There are many commercial silicone and RTV materials used for eggshell molding. Use the following during post-processing with EGGSHELL-AMB 10 to improve any inhibition issues:
    1. When cleaning parts, use acetone instead of IPA, following the same cleaning instructions for IPA from the Post-Processing Guide. Follow all SDS and safety precautions when using any solvent for cleaning parts.
    2. Dry parts in an oven at 60°C (140°F) for one hour before post curing.
    3. Post-cure parts for 180 minutes.
    4. Reheat parts for one hour at 100°C (212°F).
    5. Cure injected materials at an elevated temperature, such as 60°C (140°F), for one hour if material allows.
    6. Clean parts with soapy water after post-curing. Dry parts thoroughly.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

no mixing necessary

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min. (see Note)
Figure 4® TOUGH-BLK 20

General best practices apply.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min. (see Note)
Figure 4® TOUGH-GRY 10

  1. General best practices apply.

  2. For best results, use the Resin Mixer to gently stir between prints, and after the print material has been sitting overnight.

    CAUTION: Do NOT press down on the film when stirring.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 60 min (see Note)
Figure 4® TOUGH-GRY 15
  1. General best practices apply.
  2. For best results use the Resin Mixer to gently stir between prints and after the print material has been sitting overnight.

    CAUTION: Do NOT press down on the film when stirring.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 90 min.(see Note)
Figure 4® ELAST-BLK 10
  1. General Best Practices Apply.
  2. Remove parts from platform after printing. After 12 hours, large parts can detach from print platform and fall into material tray.
  3. Parts should be cleaned and cured soon after removing from the printer for best results.
  4. Aged material may have a different color hue, but it does not affect part building or usage.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 45 min.(see Note)
Figure 4® FLEX-BLK 10

  1. General best practices apply.

  2. Orient part in 3D Sprint to such that flat surfaces are not parallel with the print platform. Flat surfaces may show more support scarring than other Figure 4 materials.

Video - Figure 4 Modular 3D Sprint Training

3D Sprint YouTube Videos

Click here for full material best practices

Hand-mix with vigorous up/down motion

2 mins.

Mix resin in resin tray before printing

30 sec.

Post-Processing Guide

Cleaning Charts

 60 min.(see Note)

NOTE: Ensure that you place the build in your UV curing oven in the same orientation it was printed in, as if the bottom of the oven is the print platform.